WD2000F9MZ-76NVPL0-00010070-0.1.2.3.4.5-1920-771822-002REVA

内存卡数据恢复

WD2000F9MZ-76NVPL0-00010070-0.1.2.3.4.5-1920-771822-002REVA

HDD info report

Parameter			Value	Notes
	General
		Version	0x0002
		Controller firmware revision	01.4RQ
		Servo firmware revision	04.0H
		Overlay firmware revision	01.4SQ
		Surface format revision	EX.A01
		Read channel firmware revision	G.00003A
		Drive type	Enterprise 3.5 Inch
		Interface type	Serial ATA
		PCBA type	Entek rev 0
		ROM type	Serial Flash
		Flash size (page size)	1024 (4) kB
		DRAM size (allocated)	65536 (61468) kB
	Drive Parts Information
		Controller chip vendor	0x0000
		Controller chip revision	0x96C1
		MicroP vendor	0x0000
		MicroP revision	0x96C1
		Channel chip vendor	0x0099
		Channel chip revision	0x0011
		Preamp vendor	0x0001
		Preamp revision	0x0003
		Power chip vendor	0x0000
		Power chip revision	0x8022
	Drive Build Information
		Product ID (Ext)	0x16FE (0x0211)
		Model	WDC ROM MODEL-VIVALDI-
		Serial number	WDC-ROM SN# XYZ----
		DCM
		Original built date
		Reconfiguration date
		Drive platters	3
		Physical heads	6
		Virtual heads	1
		Depop bit map	0x00
		Zones	61
		Servo wedges	384
		Negative cylinders	256
		Spindle RPM	7200
		User cylinders	0
		Cylinder wedge skew	30
		Head skew	120
		Cluster skew	200
	Error Correction Information
		No. of interleaves in OTF	0
		Number of ECC + CRC Bytes	0
		No. of bytes(symbols) corrected by OTF	0(0)
		No. of bytes(symbols) corrected by FW	0(0)
		Feature flags	0x6DE3FBB6
	Jumper Settings
		Jumper setting value	0x0000
		Master jumper	OFF
		Slave jumper	OFF
		CSEL jumper	OFF
	ReloList File Information
		Number of relocations	0
		Number of tares	0
		Number of Ftares	0
		Max remaining possible relos	0
		Number of consumed spares	0
		Last LBA of spare pool	977 098 752
	Drive Format Information
		Tracks per inch (in KTPI)	0
		Area Density in 100MB (per platter)	10005
		Format Type(0)	primary format
	SATA IPM Timers
		Partial	500 ms
		Slumber	2500 ms

内存卡数据恢复

State sector

Parameter			Value	Notes
	Common
		Format Version	1
		VSC Implementation, Minor	1
		VSC Implementation, Major	4
		Max Action Code Supported	172
	Last operation
		Last Cmd Type	3	VSC Data CMD
		Last Cmd Register	176	0xB0
		Last VSC Cmd Action Code	13	0x000D
		Last Feature Register	213	0x00D5
		Last Sector Count Register	1	0x0001
		Last Sector Number Register	191	0x00BF
		Last Cylinder Register	0xC24F	49 743
		Last LBA High	0x0000
		Last Device Control Register	0x00
		Last Device/head Register	0xA0
		Last Task File Response Reg/Error	0x00/0x00
	Errors
		Extended Error	0x0000	SUCCESS
		Secondary Error Code	0x0000
	Info
		Host Connection Speed	3	SATA GEN2
		APM Level	0x80
		Sectors Xfer Pending to/from drive	0
		Last Task File Data	0
	Status
		Status Flags 1	0x5083
		Bit 0: VSC Command Set	Enabled
		Bit 1: Smart is	Enabled
		Bit 2: Legacy Native Mode	Not supported
		Bit 3: Instability bit is	cleared
		Bit 4: Pending VSC Tx from Drive to Host	[NO]
		Bit 5: VSC Command currently executing in background	[NO]
		Bit 9: At least one DBS event occurred since the last clear DRM	[NO]
		Bit 10: At least one reset-while-busy event occurred since the last clear DRM	[NO]
		Bit 11: Drive is powered up in Standby and has not spun	[NO]
		Bit 13: Drive in Queue Abort Mode	[NO]
		Bit 16: VSC POR Reset Occurred	[NO]
		Bit 17: Power On Reset Occurred	[NO]
		Bit 18: Hardware Reset Occurred	[NO]
		Bit 19: Software Reset Occurred	[NO]
		Bit 20: Debug Stop Occurred	[NO]
		Bit 25: Write Fault Occurred	[NO]
		Bit 26 & 27: Drive Protect State	0	UnLock
		Bit 28: Encryption Key Loaded	[NO]
		Bit 30-31: Offline Pending Status	0	NO OL PENDING
		Current Drive State 1	0x0	Idle
		Current Drive State 2	0x0
		BG DST/Smart OL State	Suspend
		Test Type	0x0	No DST or Smart OL
		Progress Indicator	0x0
		Write Fault LBA	0
	Position
		Current LBA	0
		Current Track Offset	0
		Virtual cylinder of current active track	0
		Virtual head of current active track	0
		Servo Track Offset of current active track	0	(for VDT drives only)
		Virt Servo Cylinder of current active track	274944	(for VDT drives only)
		Data-to-Servo Conversion Offset	0	(for VDT drives only)
		Current Data Zone	0
		Current Wedge Start	0
		Current Wedge Size	0
	Temperature
		Drive Temperature (avg)	128
		Junction Temperature (degree)	128
		Flex Temperature (degree)	34
		Coil Temperature	0
	Servo
		Servo Status	0x0064
		Seed Cyl	0
		Seed Head	0
		Seed Sector	0
		Sector Skew	0
		Wedge Skew	0
	Debug
		Debugstop Code	0x0000
	PST Information
		PTM File Id	0x00
		PTM Test Id	0x00
		Current VSC Command	0x0D
	PTM
		PTM Status	00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

jls123456789@

:):):):):):):):):):)

PMX_Sys

Awesome ;)